Search found 55 matches

by hpd14thu
Mon Sep 23, 2019 7:35 am
Forum: ROMS Bugs
Topic: Time input problem: DIAG speed trouble NaN
Replies: 0
Views: 102

Time input problem: DIAG speed trouble NaN

Hello,everyone! I have some problems with my boundary condition. When I use Gra and don't input any boundary file, the case runs well. But when I input boundary file and use RadNud, the model blows up from the beginning and show NaN. I checked my boud.nc, but there isn't any NaN in it. I am sure tha...
by hpd14thu
Thu Sep 19, 2019 2:00 am
Forum: ROMS Discussion
Topic: WET_DRY option results in too much land_mask?
Replies: 2
Views: 87

Re: WET_DRY option results in too much land_mask?

You are telling the model that it can never have less than 10 m water depth in the "wet" parts. You might try something rather smaller for DCRIT, like 0.5 m. Then you'd have to have 9.5 m of water leaving due to the storm surge before a spot became "dry". Thank you for your reply, Kate! I misunders...
by hpd14thu
Wed Sep 18, 2019 3:19 pm
Forum: ROMS Discussion
Topic: The xi_position and eta_position of rivers.nc input
Replies: 4
Views: 211

Re: The xi_position and eta_position of rivers.nc input

wilkin wrote:There is a detailed explanation of the conventions for specifying river sources here in WikiROMS:

https://www.myroms.org/wiki/River_Runof ... _Eposition
Thank you! It's very helpful!
by hpd14thu
Wed Sep 18, 2019 3:16 pm
Forum: ROMS Discussion
Topic: open boundary for future projection of CMIP6 downscaling
Replies: 11
Views: 514

Re: open boundary for future projection of CMIP6 downscaling

According to rtoste's suggestion, I recreated the initial and boundary files from CMIP for my simulation, then it works well without blow-up problem. Good evening, I have the same question. I wonder that if your inition data and boundary data are from different database, which cause this problem? T...
by hpd14thu
Wed Sep 18, 2019 2:57 pm
Forum: ROMS Discussion
Topic: WET_DRY option results in too much land_mask?
Replies: 2
Views: 87

WET_DRY option results in too much land_mask?

Hello everyone, I am runing a costal area case and I just force it by wind stress.The running time is 16days. I set hmin as 10m and turn on the WET_DRY option( I set WET_DRY parameter as 10m , too). But I don't know why there are too much land mask generated in the last half of my calculation time, ...
by hpd14thu
Tue Sep 17, 2019 7:19 am
Forum: ROMS Bugs
Topic: I/O syntax error
Replies: 2
Views: 274

Re: I/O syntax error

Maybe some variables are not consistent in your input files(.in file and some input nc files). You can try CPP options kate told you, I think it works well
by hpd14thu
Sun Sep 15, 2019 6:01 pm
Forum: ROMS Bugs
Topic: DIAG speed trouble / gridbuilder
Replies: 3
Views: 195

Re: DIAG speed trouble / gridbuilder

With a minimum grid cell size of ~4 km you should be well within CFL stability with such a small time step, so that's not your problem. The log indicates a 3rd record was written to the restart file on blow-up, so you should plot what's in there and look for a location that is causes trouble. It co...
by hpd14thu
Fri Sep 13, 2019 11:47 am
Forum: ROMS Tools and Techniques
Topic: How to use the matlab script for pre- &post- processing
Replies: 2
Views: 290

Re: How to use the matlab script for pre- &post- processing

Now, I have created several forcing files according to the script of D_ECMWF2ROMS. However, when i generate the initial and boundary files using d_mercator2roms.m and D_OBC_MERCATOR.m, I can not find the source dataset of mercator ocean data. So my problem is how to download the mercator ocean data...
by hpd14thu
Wed Sep 11, 2019 1:22 pm
Forum: ROMS Bugs
Topic: DIAG speed trouble / gridbuilder
Replies: 3
Views: 195

DIAG speed trouble / gridbuilder

Dear all, I'm trying to run ROMs by bulk forcing,and initial condition, but it blows up. Because my area is near the coast and my blow-up point is in the shallow water area(~10m), I try to decrease my dt from 300s to 10s and decrease my N from 36 to 25. It does work but it just delay the time of blo...
by hpd14thu
Tue Sep 10, 2019 10:33 am
Forum: ROMS Bugs
Topic: DIAG speed trouble
Replies: 4
Views: 305

DIAG speed trouble

Dear all, I'm trying to run ROMs by bulk forcing, river forcing and boundary values, but it blows up from the beginning. And ROMS doesn't show the details. I wonder that which problems can result in this blow-up, then I can have a check. Thank you! ---------------------------- mab Operating system :...
by hpd14thu
Tue Sep 10, 2019 1:55 am
Forum: ROMS Discussion
Topic: if I can set hc=Tcline>hmin?
Replies: 7
Views: 241

Re: if I can set hc=Tcline>hmin?

It depends on which vertical "transform" function you use. The old one needed Tcline <= hmin, but the new one does not. I'm sure there's plenty of code still around from the bad old days. I use: Vtransform == 2 ! transformation equation Vstretching == 4 ! stretching function THETA_S == 7.0d0 ! surf...
by hpd14thu
Mon Sep 09, 2019 4:05 pm
Forum: ROMS Discussion
Topic: if I can set hc=Tcline>hmin?
Replies: 7
Views: 241

if I can set hc=Tcline>hmin?

Hello everyone,

I found that in init.matlab pre-processing file, people set hc=min(hmin,Tcline), but my hmin is very small(2m), so I want to set a bigger hc=Tcline(50m)(change the code hc=min(hmin,Tcline) to hc=Tcline). I wonder that if it's OK?

Thank you!!
by hpd14thu
Sat Sep 07, 2019 7:32 am
Forum: ROMS Discussion
Topic: The xi_position and eta_position of rivers.nc input
Replies: 4
Views: 211

Re: The xi_position and eta_position of rivers.nc input

kate wrote:It refers to i, j. The western-most u-point is at i=1.
Thank you so much!
by hpd14thu
Fri Sep 06, 2019 6:12 pm
Forum: ROMS Discussion
Topic: The xi_position and eta_position of rivers.nc input
Replies: 4
Views: 211

The xi_position and eta_position of rivers.nc input

Hello everyone, I have a question about the xi_position and eta_position of rivers.nc input. I wonder the xi_position and eta_position refer to the internal grid or the rho grid(contains two more external columns). If it refers to the rho grid, we can use i and j But if it refers to the internal gri...
by hpd14thu
Sat Mar 16, 2019 2:43 am
Forum: ROMS Discussion
Topic: parameter hc and Tcline
Replies: 2
Views: 427

Re: parameter hc and Tcline

wilkin wrote:The parameters Tcline and hc are explained here:
https://www.myroms.org/wiki/Vertical_S-coordinate

The page concludes with some example stretching generated with scoord.m which is in the Matlab repository available on myroms.org.
Thank you for your reply :mrgreen:

Peida
by hpd14thu
Fri Mar 15, 2019 8:48 am
Forum: ROMS Discussion
Topic: Which tool is the stablest tools to create ROMS grid?
Replies: 20
Views: 2715

Re: Which tool is the stablest tools to create ROMS grid?

Hi Peida, It sounds like being able to specify exact corner coordinates would be a useful feature to add, I'll try and put something together. In the meantime you can import custom reference points in a text file as comma deliminated x,y pairs. These points will plot as small black + symbols on the...
by hpd14thu
Thu Mar 14, 2019 8:30 am
Forum: ROMS Discussion
Topic: parameter hc and Tcline
Replies: 2
Views: 427

parameter hc and Tcline

Hi all, I am writing the matlab code to generate init.nc file now. But I am not clear about the physical significance of parameter hc and Tcline . I try to Goole that but I did not find the answer. I would so appreciate if if someone can explain these parameters. Thanks for your attention and your r...
by hpd14thu
Thu Mar 14, 2019 7:23 am
Forum: ROMS Discussion
Topic: Which tool is the stablest tools to create ROMS grid?
Replies: 20
Views: 2715

Re: Which tool is the stablest tools to create ROMS grid?

Hi Victor, Unfortunately I haven't added support for creating multiple nested grids into GruidBuilder since I've only done off-line nesting. For now you'll have to add the nesting attributes manually to the attributes in the new grid to use contact.m. I'll look into it for the next time I update th...
by hpd14thu
Tue Jan 08, 2019 12:35 pm
Forum: ROMS Discussion
Topic: Doubts regarding strong surface currents
Replies: 12
Views: 2543

Re: Doubts regarding strong surface currents

But, are you only using ROMS why use the COAWST ? I agree with Ivica, if you do not use the functions of a coupled model, it does not make sense to use it. Do you use the tidal forcing and river data? What atmospheric and ocean forcing are you using? On what machine do you perform your simulations?...
by hpd14thu
Tue Jan 08, 2019 12:33 pm
Forum: ROMS Discussion
Topic: Doubts regarding strong surface currents
Replies: 12
Views: 2543

Re: Doubts regarding strong surface currents

I suggest you first to read a few papers related to the wind stress formulations in extreme events like TC, many of them are John's papers using COAWST and many Hurricane cases etc. Not to just blindly run ROMS model and then expect to get result that is perfect. For example: Bryant & Akbar in JMSE...
by hpd14thu
Tue Jan 08, 2019 11:48 am
Forum: ROMS Discussion
Topic: Too strong currents in hurricane-induced flow
Replies: 2
Views: 468

Re: Too strong currents in hurricane-induced flow

Hi hpd14thu, Thanks for your questions. 1) Are the wind speeds also overestimated compared to the data? 2) There has been an observed rolloff of drag at high wind speeds that is not coded into the current version of bulk fluxes. This will be included in the next COAWST version, but you can send me ...
by hpd14thu
Mon Jan 07, 2019 12:13 pm
Forum: ROMS Discussion
Topic: Doubts regarding strong surface currents
Replies: 12
Views: 2543

Re: Doubts regarding strong surface currents

Are you using COAWST or ROMS? Hello, I wonder that the magnitute of the wind speed you used. I also met the problem that the currents were too strong. My wind speed is up tp 58m/s. I don't know that if the scheme in ROMS can adapt to the 58m/s-wind speed, or if there is something wrong in my cpps. ...
by hpd14thu
Mon Jan 07, 2019 7:20 am
Forum: ROMS Discussion
Topic: out-of-memory problem in .nc file while pre-process
Replies: 2
Views: 458

Re: out-of-memory problem in .nc file while pre-process

lalvarez wrote:Hello there

You have to look at your files timelength, or how you set the order in your *.in file configuration

Thank you for your reply, the problems are solved!
by hpd14thu
Sun Jan 06, 2019 8:00 pm
Forum: ROMS Discussion
Topic: Too strong currents in hurricane-induced flow
Replies: 2
Views: 468

Too strong currents in hurricane-induced flow

I use the hurricane to force the upper ocean, and the wind speed is up to 55m/s. And there is a problem, the upper ocean's currents is too strong compared to the data. I wonder that if I have choose some cppoptions when I try the high-speed wind cases?
by hpd14thu
Sun Jan 06, 2019 5:34 am
Forum: ROMS Discussion
Topic: Doubts regarding strong surface currents
Replies: 12
Views: 2543

Re: Doubts regarding strong surface currents

Hello, I wonder that the magnitute of the wind speed you used.

I also met the problem that the currents were too strong. My wind speed is up tp 58m/s. I don't know that if the scheme in ROMS can adapt to the 58m/s-wind speed, or if there is something wrong in my cpps.
by hpd14thu
Sun Nov 25, 2018 2:47 pm
Forum: ROMS Discussion
Topic: out-of-memory problem in .nc file while pre-process
Replies: 2
Views: 458

out-of-memory problem in .nc file while pre-process

Hello, I try to generate force.nc file by Matlab, and the variables in this file are Uwind, Vwind, Pair.... But the matrix of variables is too big and Matlab show that 'one or more variables sizes violate format'. So I generate two force.nc, which are corresponding to different period of time. But R...
by hpd14thu
Tue Oct 09, 2018 10:55 am
Forum: ROMS Discussion
Topic: blow-up when lateral gradient increases
Replies: 2
Views: 491

Re: blow-up when lateral gradient increases

kate wrote:Maybe you need a shorter timestep when the winds ramp up. What is the nature of your blow-up?
Thank you for your reply , I set a shorter timestep and the problem was solved.o(∩_∩)o
by hpd14thu
Mon Oct 08, 2018 4:03 pm
Forum: ROMS Discussion
Topic: blow-up when lateral gradient increases
Replies: 2
Views: 491

blow-up when lateral gradient increases

I set the U-wind and V-wind as input forcing file, when the lateral gradient of these two variales increase, the project blow-up.
So how can I solve this problem if I want to run the high lateral gradient case? Thank you!
by hpd14thu
Tue Oct 02, 2018 1:56 pm
Forum: ROMS Discussion
Topic: Parameter Theta s and theta b don't work
Replies: 2
Views: 572

Re: Parameter Theta s and theta b don't work

s_rho is not the final dimensional vertical coordinate. s_rho depends on the choice of TRANSFORM and the final z depths depend on the STRETCHING applied to s_rho. Read https://www.myroms.org/wiki/Vertical_S-coordinate There are Matlab and Python routines to compute z offline from the Vtransform, Vs...
by hpd14thu
Sun Sep 30, 2018 9:24 am
Forum: ROMS Discussion
Topic: Parameter Theta s and theta b don't work
Replies: 2
Views: 572

Parameter Theta s and theta b don't work

I set theta s=5 and theta b=0.4 , these parameters should work on the spacing of near-surface.
But the value of s_rho shows that the grid is still equidistant.

I wonder how to solve this problems, look forward to your reply.
by hpd14thu
Sun Sep 30, 2018 9:16 am
Forum: ROMS Discussion
Topic: How to set Coriolis parameter f in x-y coordinates?
Replies: 2
Views: 545

Re: How to set Coriolis parameter f in x-y coordinates?

Look at the examples in ana_grid.h (which you are presumably using to create your x/y grid). Follow one of these, like UPWELLING: Xsize=1000.0_r8*REAL(Lm(ng),r8) Esize=1000.0_r8*REAL(Mm(ng),r8) depth=150.0_r8 f0=-8.26E-05_r8 beta=0.0_r8 and set f0 to the value you want. Then there is code later in ...
by hpd14thu
Sat Sep 22, 2018 12:47 pm
Forum: ROMS Discussion
Topic: How to set Coriolis parameter f in x-y coordinates?
Replies: 2
Views: 545

How to set Coriolis parameter f in x-y coordinates?

Hello, I want to use x-y coordinate instead lat-lon coordinate, but I don't know where can I set the value of parameter f. I wonder that if I should set the value in grid.nc or other place .

Hope your reply.Thanks~
by hpd14thu
Sat May 12, 2018 11:21 am
Forum: ROMS Bugs
Topic: all result = 0?
Replies: 22
Views: 3357

Re: all result = 0?

Hello,here is the part about reading the forcing file in result.out. I wonder that if there is any problems in reading part. I just set one variable : Uwind = 8, all of other values =0 LM: GET_STATE - Read state initial conditions, t = 0 00:00:00 (Grid 01, File: zfirst_init_cco.nc, Rec=0001, Index=1...
by hpd14thu
Sat May 12, 2018 6:20 am
Forum: ROMS Bugs
Topic: all result = 0?
Replies: 22
Views: 3357

Re: all result = 0?

You probably set all sea grids as land pixels. So all the velocity/kinetic energy are zeros, but total potential energy and volume are not since the calculation of these diagnostics are not masked off. Can you make a plot your land/sea masks to check? -Bin Hello,Bin Thank you for your help and sugg...
by hpd14thu
Fri May 11, 2018 12:22 pm
Forum: ROMS Bugs
Topic: Bug when write the values into forcing.ncfile
Replies: 2
Views: 810

Re: Bug when write the values into forcing.ncfile

And here is my matlab file which used to write values into forcing.nc file: %1) Enter start time of forcing file, in seconds. % This time needs to be consistent with model time (ie dstart and time_ref). % See *.in files for more detail. time = [0 1 2]; sms_time = [0 1 2]; %4) Obtain grid information...
by hpd14thu
Fri May 11, 2018 11:58 am
Forum: ROMS Bugs
Topic: all result = 0?
Replies: 22
Views: 3357

Re: all result = 0?

Reading the log file output your quoted WRT_HIS - wrote history fields (Index=2,2) into time record = 0000082 82 0 00:00:01 0.000000E+00 9.608405E+01 9.608405E+01 4.601201E ... that says to me the model has run for only 1 second of simulated time. If so, you're not going to see much action. What is...
by hpd14thu
Fri May 11, 2018 11:28 am
Forum: ROMS Bugs
Topic: Bug when write the values into forcing.ncfile
Replies: 2
Views: 810

Re: Bug when write the values into forcing.ncfile

And here is my frc_uvstress.cdl netcdf frc_uvstress { dimensions: xi_rho = 100 ; xi_u = 99 ; xi_v = 100 ; eta_rho = 200 ; eta_u = 200 ; eta_v = 199 ; sms_time = UNLIMITED ; // (0 currently) variables: float sms_time(sms_time) ; sms_time:long_name = "surface momentum stress time" ; sms_time:units = "...
by hpd14thu
Fri May 11, 2018 11:28 am
Forum: ROMS Bugs
Topic: Bug when write the values into forcing.ncfile
Replies: 2
Views: 810

Bug when write the values into forcing.ncfile

I'm a beginner at computer programming. I use the frc_uvstress.cdl file in ".../trunk/Data/ROMS/CDL" , and I transfered it into forcing netcdf file. Then I use a matlab file(which named str_cdl_nc.m) to write values(sms time, sustr, svstr) into the ncfile. But when I check the forcing.nc file. The v...
by hpd14thu
Fri May 11, 2018 2:44 am
Forum: ROMS Bugs
Topic: sustr and svstr Value has not been read
Replies: 11
Views: 1726

Re: sustr and svstr Value has not been read

Dear, Your attached file is completely wrong :shock: and it's not really readable for the ROMS, such attributions, dimensions and time format. I suggest you that follow directory :arrow: ".../trunk/Data/ROMS/CDL" it can help you to find your questions :?: . Good luck to you Farshid Thanks a lot! I'...
by hpd14thu
Thu May 10, 2018 4:46 pm
Forum: ROMS Bugs
Topic: all result = 0?
Replies: 22
Views: 3357

Re: all result = 0?

To add to Kate's suggestion, I would run this model for about 10 time steps having compiled with debug on in the compile script (however you compile the model). Run in scalar mode (one processor). Make sure that you turn on array bounds checking. This makes sure that arrays are defined and indexes ...
by hpd14thu
Thu May 10, 2018 2:34 pm
Forum: ROMS Bugs
Topic: sustr and svstr Value has not been read
Replies: 11
Views: 1726

Re: sustr and svstr Value has not been read

Dear, As stated by Katherine and John, such errors :arrow: (GET_2DFLD - error while reading variable: or GET_3DFLD - error while reading variable:) are due to the definition of input variables. To avoid encountering such a problem is essential check consistency of the variables in ".nc" file with t...
by hpd14thu
Thu May 10, 2018 2:25 pm
Forum: ROMS Bugs
Topic: sustr and svstr Value has not been read
Replies: 11
Views: 1726

Re: sustr and svstr Value has not been read

Gridded: LonMin = -13.6075 LonMax = 35.9397 LatMin = 97.6335 LatMax = 146.0208 Model: LonMin = 0.0000 LonMax = 0.0000 LatMin = 0.0000 LatMax = 0.0000 Your model grid doesn't appear to have lat,lon values in it. The gridded forcing does have them, though one might question your latitude values. Are ...
by hpd14thu
Thu May 10, 2018 1:36 pm
Forum: ROMS Bugs
Topic: all result = 0?
Replies: 22
Views: 3357

Re: all result = 0?

Given the values in the wind forcing file (10^34), I think these are all "missing values" for netcdf. Are you sure that you assigned variables to the forcing file? I would plot the wind speeds in the forcing file to see that they are what you wanted. If the forcing file is ok, then make sure that t...
by hpd14thu
Sun May 06, 2018 5:23 pm
Forum: ROMS Bugs
Topic: sustr and svstr Value has not been read
Replies: 11
Views: 1726

Re: sustr and svstr Value has not been read

Gridded: LonMin = -13.6075 LonMax = 35.9397 LatMin = 97.6335 LatMax = 146.0208 Model: LonMin = 0.0000 LonMax = 0.0000 LatMin = 0.0000 LatMax = 0.0000 your forcing file does not have any grid data. each field needs an attribute of lon and lat. see here https://www.myroms.org/forum/viewtopic.php?f=1&...
by hpd14thu
Sun May 06, 2018 5:02 pm
Forum: ROMS Bugs
Topic: sustr and svstr Value has not been read
Replies: 11
Views: 1726

Re: sustr and svstr Value has not been read

you basically have this set: /* Forcing */ # ifdef WRF_MODEL ... # else /*# define BULK_FLUXES/* # define ANA_SMFLUX # endif so you have ana_smflux on. that will look for analytical values and they are most likely set to 0. so you would want to use #undef ANA_SMFLUX and then it will look for su/vst...
by hpd14thu
Sun May 06, 2018 4:55 pm
Forum: ROMS Bugs
Topic: all result = 0?
Replies: 22
Views: 3357

Re: all result = 0?

kate wrote:I don't know what to check either, but you need to be looking at the values in all the input and output files. Where is that weird 1e34 coming from? I like ncview for viewing these files.
by hpd14thu
Sun May 06, 2018 3:07 pm
Forum: ROMS Bugs
Topic: sustr and svstr Value has not been read
Replies: 11
Views: 1726

sustr and svstr Value has not been read

My force file contains sustr and svstr , but when I run it , I find that these two variable has not been read. I consider that there are some problems in my head file , but I don't know which CPP option I should add into head file. Here is my head file: /* ** svn $Id: sandy.h 25 2007-04-09 23:43:58Z...
by hpd14thu
Sun May 06, 2018 6:00 am
Forum: ROMS Bugs
Topic: all result = 0?
Replies: 22
Views: 3357

Re: all result = 0?

【and when I checked the calculation process in his file , I found that the sus ,the svs..in each step is 10^34, I don't know if it means that the calculation is blow out.】 It means you have some serious problems. I'm not sure what, but I'd look carefully at all the inputs and outputs. And here is m...
by hpd14thu
Sun May 06, 2018 5:52 am
Forum: ROMS Bugs
Topic: all result = 0?
Replies: 22
Views: 3357

Re: all result = 0?

Here is the file which used to generae force.nc : %1) Enter name of netcdf forcing file to be created. % If it already exists it will be overwritten!!. % fn='zfirst_wind_cco.nc'; fn='zfirst_wind_cco.nc'; %2) If you want to read the forcing data from another netcdf file, then % enter read_forcing=1 a...
by hpd14thu
Sun May 06, 2018 5:43 am
Forum: ROMS Bugs
Topic: all result = 0?
Replies: 22
Views: 3357

Re: all result = 0?

【and when I checked the calculation process in his file , I found that the sus ,the svs..in each step is 10^34, I don't know if it means that the calculation is blow out.】 It means you have some serious problems. I'm not sure what, but I'd look carefully at all the inputs and outputs. Thank you for...
by hpd14thu
Sat May 05, 2018 3:05 am
Forum: ROMS Bugs
Topic: all result = 0?
Replies: 22
Views: 3357

Re: all result = 0?

The forcing file just contains frc_bulk variables:
Uwind , Vwind , Pair..
But I don't use ustress adn vstress
by hpd14thu
Sat May 05, 2018 2:10 am
Forum: ROMS Bugs
Topic: all result = 0?
Replies: 22
Views: 3357

Re: all result = 0?

And here is my result: Lateral Boundary Conditions: NLM ============================ Variable Grid West Edge South Edge East Edge North Edge --------- ---- ---------- ---------- ---------- ---------- zeta 1 Closed Closed Closed Closed ubar 1 Closed Closed Closed Closed vbar 1 Closed Closed Closed Cl...
by hpd14thu
Sat May 05, 2018 1:57 am
Forum: ROMS Bugs
Topic: all result = 0?
Replies: 22
Views: 3357

Re: all result = 0?

/* ** svn $Id: sandy.h 25 2007-04-09 23:43:58Z jcwarner $ ******************************************************************************* ** Copyright (c) 2002-2007 The ROMS/TOMS Group ** ** Licensed under a MIT/X style license ** ** See License_ROMS.txt ** ******************************************...
by hpd14thu
Sat May 05, 2018 1:57 am
Forum: ROMS Bugs
Topic: all result = 0?
Replies: 22
Views: 3357

Re: all result = 0?

! Application title. TITLE = ZFIRST ! C-preprocessing Flag. MyAppCPP = ZFIRST ! Input variable information file name. This file needs to be processed ! first so all information arrays can be initialized properly. VARNAME = /home/hpd14/Documents/COAWST_V3.2/ROMS/External/varinfo.dat ! Number of neste...
by hpd14thu
Sat May 05, 2018 1:56 am
Forum: ROMS Bugs
Topic: all result = 0?
Replies: 22
Views: 3357

all result = 0?

Hello ,every one,I just use a grid file, a initial file and a easy wind file, in order to calculate the flow forced by the wind. But the result( u,v ,salt...) is zero. I tried a lot ,but it didn't work. I really need your help, thank you!

Here is my in.file and headfile